BORA NGX 50 in. Clamp Edge Saw Guide Extension

I got this to help me cut large pieces of plywood for some upcoming woodworking projects. I expect this to work perfectly in assisting me in handling full sheets of plywood, OSB, MDF, and anything else that comes in large sheets – can’t wait to get started this weekend. The track and attachments are very well made and the instructions included will help greatly when setting this up and using it.

This clamp/guide is invaluable for table saw free environments. I couldn’t recommend it enough!

This guide makes cutting sheets of plywood, oriented strand board and composite siding much easier. In my opinion, this is a must have for the DIY handyman. Matched with the saw sled, you can cut straight edges up to fifty inches. My biggest concern is that the saw sled is made of plastic and I don’t know how much rough use it can handle. I have always had a problem free cutting sheet material squarely and this set up will help accomplish precise, straight edges.

This guide is easy to use for making long crosscuts of plywood. Very light, but held up well as I cut up seven sheets of plywood to build four cabinets

Cuts straight lines and is a great tool. Guide does stick while cutting and adhesive tape starts to peel off when not in use.

I have used a few different clamp edge guide before so I am familiar with this type of product. This one is the best one that I have used by far. For me, it is the clamping action that makes it stand out. This may seem simple but other manufacturers have not gotten this perfect in my opinion. The clamp holds very tight without squeezing the material too much. Others will either slip because they are not tight enough or they will be so tight that either the edge guide or the material is bowed. Bora gets it perfect!

THis is a much better system than my fist clamp on guide. The clamp on to the board section is mostly aluminum. The saw sled is mostly plastic. My only problem was locating the proper tool to get the sled to fit my circular saw. Once that was sorted out it was smooth sailing. This is much more precise than the early model I had. The light weight will also make this tool very portable. That only leaves me looking at the new battery operated saws.

This tool is like having a portable track saw. I most recently used it for ripping and cross cutting sheets of plywood and 4’x8′ PVC trim sheets. And using it with the caddy/sled/sawplate/whatever-you-want-to-call-it, which attaches to the saw, sure beats my previous method. No more fighting an imperfect 2×4 to stay flush. The caddy fits on two of my 7 1/4″ saws (one corded, one cordless), as well as my little 6 1/2″ cordless. At first I struggled to attach the saws, but that was because I wasn’t lifting the blade. Once attached, you lower the saw blade to make sure there’s reasonable cutting depth (keep in mind the caddy’s clamps should be placed as to not interfere with the saw’s motor/housing etc… I made that mistake too). That brings me to the paper instructions”¦. Would have been nice if they were clearer. Bora’s website wasn’t any help either”¦ I had to goto youtube to figure it out. There are a lot of fine adjustments required to get the saw perfectly straight in the caddy, so I’ve left my corded saw in it so it’s ready to go for the next project.The guide comes in two pieces, which when combined provides 100″. Keep in mind when you only use the main piece you’ll get a little less than a 50″ cut due to the clamps on each end. Would have been nice if this guide had quick change/setup capability to go from 55″ to 100″. Assembly to 100″ requires removing a few screws and then screwing the ends together. Of course, then you have to reverse the process to take it apart for storage. I greatly appreciate the hanging hooks on both guides since I can get them out of the way when not in use.The 50″ and 100″ non-chip adhesive tape strip, is a nice idea in theory. In practice, it’s useless in my opinion unless you (a) adhere it perfectly straight (although it will be kinda straight if not perfect after the first cut); and (b) make only straight cuts. If you do a beveled cut you’ll cut the tape unless you flip the whole sled contraption around to the other side of the track”¦. and doing so changes the blade’s position. I haven’t tried the two additional track clamps for angle cutting yet because I haven’t needed angular cuts. To attach the track clamps you have to remove the ends and slide them onto the track. Overall this seems well built and it’s a very helpful tool for the DIYer like me who wants the advantages of a track saw. I’m pleased with it.

I really could have used this when I was building 4 barn doors for my basement. But I have two more to go and this will make the job much easier. It’s a pretty simple setup – the bars clamp easily to the work piece. And if it’s just straight cuts you can get away without the sled, just keep your saw pressed up against the track. The sled is a little tricky to attach straight but that’s more due to me being new to using a track saw. Couple of YouTube videos later and it was easy to figure out. And using the sled will ensure the saw doesn’t stray. All parts are very sturdy, very little flex in the bars. And the additional track clamps are a great addition – you can use bar clamps or C clamps, but to have clamps purpose built for this is much better. All in all, this is hands down better than screwing in scrap pieces of wood to serve as my guide and then having to fill holes. My only complaint, like others, is the instructions. Definitely not the easiest to follow.

It’s straight and it locks. Feels pretty solid but doesn’t slide that smoothly. It can give one a false sense of security in thinking you are making straight cuts but you will need to double or triple check before you cut. When paired with the bora saw base plate it is even more the case to triple check your lines, measurements and fasteners as things can get out of adjustment after each pass. Overall can produce straight and accurate cuts but it will take a long time and adjustment(s).