BORA Steel 100 in. NGX Clamp Edge Deluxe Set (5-Piece)

Awesome. I can now cut straight with my circular saw.

The Bora NGX is a great product for ensuring straight cuts! I use it by itself most of the time but it also has accessories that can be used with saws, routers, and jig saws.

So glad I have one of these. While I admittedly haven’t used it much, it has been great the handful of times I have put it to use. Cuts now come out perfectly straight, which was always a struggle when simply following a line or using a makeshift guide out of a straight edge and clamps. I also own the saw plate for this guide but wasn’t sure that the blade and edge were parallel nor convinced that the saw would stay firmly in place, so I never actually used it to cut anything. One of these days I’ll give it another shot.Back to the guide:. There’s 50″ between the jaws, so cutting a 4×8 piece of plywood across the shorter side isn’t a problem. Once tightened down, they grip the edges really well – no issues with them coming loose. Now, I’m not sure if this is a design issue or a feature, but once you loosen the clamp, you kind of have to fiddle with it in order to move the jaw. Kind of annoying but not a deal breaker. Another thing that bothers me is the fact that the critical parts (jaws, clamp) are made out of plastic. Should be fine for regular homeowner use, but longevity is a concern. One thing to note is that the clamp sticks out close to 3″ when it is tightened – just something to consider as this may be a problem if you have to set this up on the floor.

Boro NGX 5-Piece Clamp Edge Deluxe Set is an excellent way to cut sheet-goods and other tasks. The set consists of two guide rail pieces to handle 4 x 8 panels. One aluminum guide is used to cross-cut the four foot side with a 50-inches long track. For the rip cut, add the second 50-inch guide extension to the first guide for a 100-inch length, a little over 8-feet long. The two set of tracks are held together securely with metal bars and four screws. The track is then laid on top of the supported panel and two edge clamps on each side, under the guide, are easily tightened to give a rock solid grip onto the panel edges. Two included track clamps are also included if you want an angle cut, any angle can be cut up to 90-degrees is possible. You can cut full 4 x 8 panels or smaller sizes easily with this setup. The circular saw making the cut can run along the edge of the aluminum track guide or attached with the provided saw sled that slips into the aluminum guide securely in a groove. Once the saw is mounted to it runs along a groove in the guide preventing the saw from wandering, assuring a straight cut.. It works similar to a track saw. Included in the set used with the sled plate are two lengths of 3M non-chip strips that attach to the bottom for riding on the panel. It minimizes any top edge tear-out for a cleaner cut. This is useful for bonded veneers; although not needed for other panels like MDF or construction grade plywood. The sled is made of sturdy plastic with honeycomb reinforcement that is rigid, doesn’t flex. The saw is held-down with hold-down screws and clips, can be positioned and removed easily. Bora also offers, optionally, other tool sled plates to hold routers and a jig saws that work with the track guide, too.I own a portable table-saw and continue to prefer Bora’s system for breaking down sheet-goods resting on two saw horses. It is safer than handling large sheets alone on the table saw. It gives me more control making the cut safe and clean.

It’s a bit difficult to set up. A lot of folks recommend using it with a dedicated saw and keeping that saw attached to the plate, which I think would help. But it makes excellent straight cuts, and sets up much faster than my old straight edge.

BORA 5-Piece Clamp Edge Saw Guide. Well built and nice features. When the extension is added, it can handle an eight foot piece of plywood. I dropped this product down a point because the instructions could use a lot more detail. Especially on installing the non-chip strips. Took me a while and a phone call to figure it out. First, straighten the strips out as much as possible. Second, the blue covering needs to be removed from the double sided tape. If your not careful, you’ll remove the tape along with the blue covering. One strip on each guide. Make sure the strip is on the same side of each guide. The side of the strip that has the tape goes on one side of the bottom of the guides (lower step on bottom). When the strip is installed, the tape side of the strip should be level with the upper step of the guide. The other edge of the strip should overhang the edge of the guide. The saw should be used on the side of the guide with the strip attached (overhang). Mounting the saw to the saw plate was easier and is adjustable in all directions. I stored my saw with the plate attached. The adjustible clamp holds the board tightly and gives you a ridgit, straight guide to cut on. Can be used with or without the sawplate. Using the saw plate is easier.

I have used a few different clamp edge guide before so I am familiar with this type of product. This one is the best one that I have used by far. For me, it is the clamping action that makes it stand out. This may seem simple but other manufacturers have not gotten this perfect in my opinion. The clamp holds very tight without squeezing the material too much. Others will either slip because they are not tight enough or they will be so tight that either the edge guide or the material is bowed. Bora gets it perfect!

It took me a little while to understand on how to mount my saw but once the light bulb in my head turned on it was easy. One of the clamps broke and sent Bora a picture of it and they sent me a new one right away. Good Customer Service!!!!!!!!!!

Overall I like this Bora system. It clamps tight and did not bow while sawing. Once I got my circular saw mounted on the saw plate things went fast. I am glad I bought this system and I have used it often.

Wish I had this a few years ago!